Phone Fob 12 Steps Instructables Step 1: materials and tools: sewing machine (not pictured) iron and ironing board (not pictured) scissors two (2) pairs (one for cutting fabric, one for snipping threads) #1. rotary cutter to cut fabric and interfacing or use scissors #2. pliers for closing the key fob #3. Step 9: making the 6 strand diamond knot. make your final crown knot slightly loose. hook the lower right cord end clockwise around the next arched cord and insert it through the center of the crown knot (see image). repeat for remaining 5 cords. in the end, all cords will pop from the center.
Phone Fob 12 Steps Instructables Step 3: glue. use a hot glue gun to carefully glue the bearings into all four .5” holes. be sure not to get glue into the bearings as this will prevent them from spinning freely. glue the 12” long, 1.25” diameter pipe into the 1.25” hole in the end cap. the end of the pipe should be even with the inner ceiling of the cap. Step 4: gluing the veneer to the case. now add some glue to the case and spread it out evenly. i used regular school glue at first, but i don't recommend using that instead i would use super glue or some better solution. then place down the veneer onto the case and weigh it down for a while. Ok, this step is all about making the bit that holds the phone. if you want a plain key fob you can skip this step. find the middle of the leather strap you just cut, mark it with a dot. now measure 1.5cm either side of this dot and make two more marks like shown. using the last two dots as guides measure down 7mm and make another two dots. To. activate the solution you want to add your hydrogen peroxide 3 5% solution in a 2 to 1 ratio. two parts muratic acid to one part hydrogen peroxide. after the peroxide has been added to your muratic acid the mixture should start to bubble, and. the base metals should begin to dissolve.
Phone Fob 12 Steps Instructables Ok, this step is all about making the bit that holds the phone. if you want a plain key fob you can skip this step. find the middle of the leather strap you just cut, mark it with a dot. now measure 1.5cm either side of this dot and make two more marks like shown. using the last two dots as guides measure down 7mm and make another two dots. To. activate the solution you want to add your hydrogen peroxide 3 5% solution in a 2 to 1 ratio. two parts muratic acid to one part hydrogen peroxide. after the peroxide has been added to your muratic acid the mixture should start to bubble, and. the base metals should begin to dissolve. Step 3: arduino with bluetooth. this code is in the public domain. pinmode(rxd, input); setup the arduino to receive input from the bluetooth shield on digital pin 6. pinmode(txd, output); setup the arduino to send data (output) to the bluetooth shield on digital pin 7. Step 7: arduino code explained. now open doorcontrol.ino, we will need to change the rfid tag values. change rfid tag 1, 2, 3 to the hex values we got from the previous steps. look for this section in the code. change the hex values to the tags you scanned. byte tag1[4] = {0x12, 0x73, 0xe5, 0x56}; rfid tag 1.
Phone Fob 12 Steps Instructables Step 3: arduino with bluetooth. this code is in the public domain. pinmode(rxd, input); setup the arduino to receive input from the bluetooth shield on digital pin 6. pinmode(txd, output); setup the arduino to send data (output) to the bluetooth shield on digital pin 7. Step 7: arduino code explained. now open doorcontrol.ino, we will need to change the rfid tag values. change rfid tag 1, 2, 3 to the hex values we got from the previous steps. look for this section in the code. change the hex values to the tags you scanned. byte tag1[4] = {0x12, 0x73, 0xe5, 0x56}; rfid tag 1.
Phone Fob 12 Steps Instructables
Comments are closed.