Nissan Rogue Oem Transmission Cooler Install Hints Youtube A short video with a few tips of how to add an aftermarket cooler to help with the transmission overheating that these vehicles suffer with. 1) take out air intake remove 3 screws, wiggle out the top air intake. 2) pull the cylindrical air intake coming from the fender area. 2) take out bumper 4 push pins on top, 4 push pins on bottom, 2 x t20 torx and 2 x 10 mm (not exactly sure on the size) on each side. 3) take out battery.
Nissan Rogue Service Manual Fluid Cooler Hose Removal And Over the summer i installed a hayden 679 transmission cooler, it's 11" x 11 5 8" x 3 4" and was plumbed in line with the radiator based cvt cooler on my 2014 rogue. install involved taking off the nissan grill, the cooler zip tied through the condenser and radiator. i didn't remove the bumper, or the fans, i zip tied through them and then cut. Where to find the factory drilled holes for the oem tranny cooler. Paul. update it was the hayden 678 i installed, not the 677. cvt temps have reduced up to 30 degrees compared to before the installation of the cooler. the cvt now climbs hills at 180 degrees in 90 degree heat (instead of 200 210), and runs all day at 160 180. plus it actually cools down now on downhills. When it did it woud not go over 65 mph. to try a prevent it from happening again in case the above three situations occur at once again i just installed a transmission cooler. first i made a bracket to hold the cooler out of 3 4" wide aluminum. after attaching the hoses i screwed the bracket and cooler into the front bumper support.
2008 2013 Nissan Rogue Oem New 2008 2013 Nissan Rogue S 2 5l Paul. update it was the hayden 678 i installed, not the 677. cvt temps have reduced up to 30 degrees compared to before the installation of the cooler. the cvt now climbs hills at 180 degrees in 90 degree heat (instead of 200 210), and runs all day at 160 180. plus it actually cools down now on downhills. When it did it woud not go over 65 mph. to try a prevent it from happening again in case the above three situations occur at once again i just installed a transmission cooler. first i made a bracket to hold the cooler out of 3 4" wide aluminum. after attaching the hoses i screwed the bracket and cooler into the front bumper support. 4. ie works upgraded cvt transmission oil cooler compatible with nissan rogue juke sentra 2007 2013 21606 1xf0a (ie works) 4 ports to fix overheating nissan! lorraine whitaker. > “i’ve been having trouble with my nissan rogue overheating, and it turns out that the transmission oil cooler was the culprit. The nissan cvt cooler kit is an essential upgrade for your vehicle if you plan on towing or hauling heavy loads. this kit replaces the factory installed oil cooler with a larger and more efficient unit, allowing your car’s transmission to stay cool under load and increasing its life expectancy. the kit includes a new aluminum radiator, hoses.
2008 2013 Nissan Rogue Oem New 2008 2013 Nissan Rogue S 2 5l 4. ie works upgraded cvt transmission oil cooler compatible with nissan rogue juke sentra 2007 2013 21606 1xf0a (ie works) 4 ports to fix overheating nissan! lorraine whitaker. > “i’ve been having trouble with my nissan rogue overheating, and it turns out that the transmission oil cooler was the culprit. The nissan cvt cooler kit is an essential upgrade for your vehicle if you plan on towing or hauling heavy loads. this kit replaces the factory installed oil cooler with a larger and more efficient unit, allowing your car’s transmission to stay cool under load and increasing its life expectancy. the kit includes a new aluminum radiator, hoses.
Comments are closed.