Installing Ceiling Fan With Two Light Switches Shelly Lighting This use case explains how using shelly pro 2 2pm (the device) you can turn on off dual lights in a room, hall or corridor from a mobile device and or multiple physical switches in key locations. learn more about shelly pro 2 and shelly pro 2pm. installation. ⚠warning! danger of electrocution. When you press the button wall switch your light will change state. if you hold the button, the light will dim down up. if you double click the switch, the light will go to 100 %. dual button mode: if you would like to control the light with two switches buttons. input sw1: turn on and brighten the light. input sw2: turn off and dim the light.
Wiring Ceiling Fan Two Switches Shelly Lighting The switches: there are two separate light switches (they are not side by side as you'd expect, but are top and bottom and are about six inches or so apart. the top switch controls the fan and the bottom switch controls the lights. the top has a set of wires coming into the switch box on the top and bottom: top of box:. The switch outputs are connected to the shelly 1l to signal switch state. the shelly device should be configured for switch inputs as "disconnected" on both inputs. this changes the behavior of the switch positions to that of a traditional three way switch in that "on" and "off" are not positionally relevant. Upon turning the switches on we will get the output in the terminals 2 and 3. inversely, there will be no output if the switches are not turned on. so, the main circuit will be simple, we just have to combine the previous circuits and end up connecting to the double switch. fig 5: schematic diagram of connecting a light and fan using double switch. Connect the ground wire to the grounding screw or wire. 5. install switches. secure the switches in the switch box and screw on the cover plate. 6. connect wires in ceiling box. in the ceiling box, connect the black wire from the 14 3 cable to the black fan wire. connect the red wire to the blue light fixture wire.
Wiring Ceiling Fan Light With Dual Switch Shelly Lighting Upon turning the switches on we will get the output in the terminals 2 and 3. inversely, there will be no output if the switches are not turned on. so, the main circuit will be simple, we just have to combine the previous circuits and end up connecting to the double switch. fig 5: schematic diagram of connecting a light and fan using double switch. Connect the ground wire to the grounding screw or wire. 5. install switches. secure the switches in the switch box and screw on the cover plate. 6. connect wires in ceiling box. in the ceiling box, connect the black wire from the 14 3 cable to the black fan wire. connect the red wire to the blue light fixture wire. The shelly1l has the lowest maximum load of any of the shelly relays at just 4.1a continuous, which in a 110v circuit is 450watts, and in a 220v circuit is 900watts. the shelly1l does have thermal protection on it, so it can safely shut off the relay if the load is too high, but you still shouldn’t try to put more than a 4a continuous load on it. Follow your instruction manual for attaching the lighting kit. my fan has a mounting ring as well as an led light. plug the light into the fan, then screw in the mounting ring and the light with three keyhole screws. carefully lift the glass up to the fan and turn clockwise until the glass is snug. do not overtighten.
How To Wire A Ceiling Fan With Light Kit And Two Switches Shelly Lighting The shelly1l has the lowest maximum load of any of the shelly relays at just 4.1a continuous, which in a 110v circuit is 450watts, and in a 220v circuit is 900watts. the shelly1l does have thermal protection on it, so it can safely shut off the relay if the load is too high, but you still shouldn’t try to put more than a 4a continuous load on it. Follow your instruction manual for attaching the lighting kit. my fan has a mounting ring as well as an led light. plug the light into the fan, then screw in the mounting ring and the light with three keyhole screws. carefully lift the glass up to the fan and turn clockwise until the glass is snug. do not overtighten.
Ceiling Fan With Light And Remote Wiring Shelly Lighting
How To Install A Dual Ceiling Fan And Light Dimmer Switch Shelly Lighting
Comments are closed.