Cync Thermostat Wiring Configuration And Installation Guide Before begining, make sure the thermostat is in off mode. follow the steps below: initiate manual setup by pressing and holding the – and buttons together for 10 seconds. you will see the screen change to manual set up mode. use the – and buttons to toggle to the desired configuration. to determine your mode code, refer to the manual. Follow the steps outlined in the cync application or in the installation guide that is included with your cync thermostat. important: power off your circuit breaker and ensure that all equipment is fully powered off. do not proceed if voltage labels read 110v or 120v, l1 or l2 terminals are present, or high voltage warnings are present.
Cync Thermostat Wiring Configuration And Installation Guide Setting up a cync thermostat this guide will assist you to setup your new cync smart thermostat. follow the instructions in the cync app. if your cync smart thermostat is not already installed, see the cync smart thermostat installation guide. the commissioning process takes about 10 minutes and consists of 4 steps to end. see below for these. Step 1. download the cync app, powered by savant, on your smartphone. step 2. determine the thermostat wires present and complete the installation. step 3. add your cync thermostat to the cync app. for set up help, visit cyncsupport.gelighting or call 1 844 302 2943. How to install a smart thermostat (5 easy installation steps):step one: beginning the smart thermostat installation processstep two: choosing the right therm. Disconnect the wires and unscrew the old thermostat base. be careful to keep the wires from falling back into the wall. hold your cync thermostat in its new location. if the old screw holes or an unpainted area are visible, use the optional trim plate to cover them. if the cync thermostat doesn’t require the optional trim plate, skip to page 20.
Cync Thermostat Wiring Configuration And Installation Guide How to install a smart thermostat (5 easy installation steps):step one: beginning the smart thermostat installation processstep two: choosing the right therm. Disconnect the wires and unscrew the old thermostat base. be careful to keep the wires from falling back into the wall. hold your cync thermostat in its new location. if the old screw holes or an unpainted area are visible, use the optional trim plate to cover them. if the cync thermostat doesn’t require the optional trim plate, skip to page 20. Installation step 3 add your cync thermostat to the cync app for set up help, visit cyncsupport.gelighting or call 1 844 302 2943 5 for detailed step by step instructions tailored to your home’s wiring configuration, use the cync app installation guide. pc31294 ing 93129894 npi cync thermostate 6421602 14 (08 20 21) lh cn none n a not. This tool will check your thermostat wiring to confirm if it is compatible with the cync smart thermostat. to get started, turn off the power to your thermostat and remove your thermostat’s face so that you can check which wires are connected to your terminals. next step. once your thermostat's power is turned off and the face is removed, you.
Cync Thermostat Wiring Configuration And Installation Guide Installation step 3 add your cync thermostat to the cync app for set up help, visit cyncsupport.gelighting or call 1 844 302 2943 5 for detailed step by step instructions tailored to your home’s wiring configuration, use the cync app installation guide. pc31294 ing 93129894 npi cync thermostate 6421602 14 (08 20 21) lh cn none n a not. This tool will check your thermostat wiring to confirm if it is compatible with the cync smart thermostat. to get started, turn off the power to your thermostat and remove your thermostat’s face so that you can check which wires are connected to your terminals. next step. once your thermostat's power is turned off and the face is removed, you.
Cync Thermostat Wiring Configuration And Installation Guide
Cync Thermostat Wiring Configuration And Installation Guide
Comments are closed.